View M27V322-100B1_4241808.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

M27V322
32 Mbit (2Mb x16) low-voltage UV EPROM and OTP EPROM
Feature summary

3.3V 10% supply voltage in Read operation Read access time - 100ns at VCC = 3.0V to 3.6V Pin compatible with M27C322 Word-wide configurable
1

42
32 Mbit Mask ROM replacement Low power consumption - Active Current 30mA at 5MHz - Stand-by Current 60A Programming voltage: 12V 0.25V Programming time: 50s/word Electronic signature - Manufacturer Code: 0020h - Device Code: 0034h ECOPACK(R) packages available
42
FDIP42W (F)

1
PDIP42 (B)
42
1
SDIP42 (S)
May 2006
Rev 3
1/23
www.st.com 1
Contents
M27V322
Contents
1 2 Summary description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Device operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 Read mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Standby mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Two Line Output Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 System considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 PRESTO III programming algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Program Inhibit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Program Verify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 On-Board programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Electronic Signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Erasure operation (applies to UV EPROM) . . . . . . . . . . . . . . . . . . . . . . . 10
3 4 5 6 7
Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Package mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2/23
M27V322
List of tables
List of tables
Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Electronic signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 AC measurement conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Read mode DC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Programming mode DC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Read mode AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Margin mode AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Programming mode AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 FDIP42W - 42 pin Ceramic Frit-seal DIP, with window (0.315" x 0.630"), mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 PDIP42 - 42 pin Plastic DIP, 600 mils width, package mechanical data . . . . . . . . . . . . . . 19 SDIP42 - 42 lead Shrink Plastic DIP, 600 mils width, package mechanical data . . . . . . . . 20 Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3/23
List of figures
M27V322
List of figures
Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 DIP connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Programming flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 AC testing input output waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 AC testing load circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Read mode AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Margin mode AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Programming and Verify modes AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 FDIP42W - 42 pin Ceramic Frit-seal DIP, with window (0.315" x 0.630"), package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 PDIP42 - 42 pin Plastic DIP, 600 mils width, package outline . . . . . . . . . . . . . . . . . . . . . . 19 SDIP42 - 42 pin Shrink Plastic DIP, 600 mils width, package outline. . . . . . . . . . . . . . . . . 20
4/23
M27V322
Summary description
1
Summary description
The M27V322 is a 32 Mbit EPROM offered in the UV range (ultra violet erase) and OTP range. It is ideally suited for microprocessor systems requiring large data or program storage. It is organised as 2 MWords of 16 bit. The pin-out is compatible with a 32 Mbit Mask ROM. The FDIP42W (window ceramic frit-seal package) has a transparent lid which allows the user to expose the chip to ultraviolet light to erase the bit pattern. A new pattern can then be written rapidly to the device by following the programming procedure. For applications where the content is programmed only one time and erasure is not required, the M27V322 is offered in PDIP42 and SDIP42 packages. In order to meet environmental requirements, ST offers the M27V322 in ECOPACK(R) packages. ECOPACK packages are Lead-free. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. Figure 1. Logic diagram
VCC
21 A0-A20
16 Q0-Q15
E GVPP
M27V322
VSS
AI03050
Table 1.
A0-A20 Q0-Q15 E GVPP VCC VSS
Signal names
Address Inputs Data Outputs Chip Enable Output Enable / Program Supply Supply Voltage Ground
5/23
Summary description Figure 2. DIP connections
A18 A17 A7 A6 A5 A4 A3 A2 A1 A0 E VSS GVPP Q0 Q8 Q1 Q9 Q2 Q10 Q3 Q11 1 42 41 2 40 3 39 4 38 5 37 6 36 7 8 35 9 34 10 33 M27V322 11 32 12 31 13 30 14 29 15 28 16 27 17 26 18 25 19 24 20 23 21 22
AI03051
M27V322
A19 A8 A9 A10 A11 A12 A13 A14 A15 A16 A20 VSS Q15 Q7 Q14 Q6 Q13 Q5 Q12 Q4 VCC
6/23
M27V322
Device operation
2
Device operation
The operating modes of the M27V322 are listed in the Operating Modes Table. A single power supply is required in the read mode. All inputs are TTL compatible except for VPP and 12V on A9 for the Electronic Signature.
2.1
Read mode
The M27V322 has a word-wide organization. Chip Enable (E) is the power control and should be used for device selection. Output Enable (G) is the output control and should be used to gate data to the output pins independent of device selection. Assuming that the addresses are stable, the address access time (tAVQV) is equal to the delay from E to output (tELQV). Data is available at the output after a delay of tGLQV from the falling edge of GVPP, assuming that E has been low and the addresses have been stable for at least tAVQV-tGLQV.
2.2
Standby mode
The M27V322 has a standby mode which reduces the supply current from 30mA to 30A. The M27V322 is placed in the standby mode by applying a CMOS high signal to the E input.When in the standby mode, the outputs are in a high impedance state, independent of the GVPP input.
2.3
Two Line Output Control
Because EPROMs are usually used in larger memory arrays, this product features a 2 line control function which accommodates the use of multiple memory connection. The two line control function allows:

the lowest possible memory power dissipation, complete assurance that output bus contention will not occur.
For the most efficient use of these two control lines, E should be decoded and used as the primary device selecting function, while GVPP should be made a common connection to all devices in the array and connected to the READ line from the system control bus. This ensures that all deselected memory devices are in their low power standby mode and that the output pins are only active when data is required from a particular memory device.
7/23
Device operation
M27V322
2.4
System considerations
The power switching characteristics of Advanced CMOS EPROMs require careful decoupling of the supplies to the devices. The supply current ICC has three segments of importance to the system designer: the standby current, the active current and the transient peaks that are produced by the falling and rising edges of E. The magnitude of the transient current peaks is dependent on the capacitive and inductive loading of the device outputs. The associated transient voltage peaks can be suppressed by complying with the two line output control and by properly selected decoupling capacitors. It is recommended that a 0.1F ceramic capacitor is used on every device between VCC and VSS. This should be a high frequency type of low inherent inductance and should be placed as close as possible to the device. In addition, a 4.7F electrolytic capacitor should be used between VCC and VSS for every eight devices. This capacitor should be mounted near the power supply connection point. The purpose of this capacitor is to overcome the voltage drop caused by the inductive effects of PCB traces.
2.5
Programming
When delivered (and after each erasure for UV EPROM), all bits of the M27V322 are in the "1" state. Data is introduced by selectively programming "0"s into the desired bit locations. Although only "0"s will be programmed, both "1"s and "0"s can be present in the data word. The only way to change a "0" to a "1" is by die exposition to ultraviolet light (UV EPROM). The M27V322 is in the programming mode when VPP input is at 12.V, GVPP is at VIH and E is pulsed to VIL. The data to be programmed is applied to 16 bits in parallel to the data output pins. The levels required for the address and data inputs are TTL. VCC is specified to be 6.25V 0.25V.
2.6
PRESTO III programming algorithm
The PRESTO III Programming Algorithm allows the whole array to be programed with a guaranteed margin in a typical time of 100 seconds. Programming with PRESTO III consists of applying a sequence of 50s program pulses to each word until a correct verify occurs (see Figure 3). During programing and verify operation a MARGIN MODE circuit must be activated to guarantee that each cell is programed with enough margin. No overprogram pulse is applied since the verify in MARGIN MODE provides the necessary margin to each programmed cell.
8/23
M27V322 Figure 3. Programming flowchart
VCC = 6.25V, VPP = 12V
Device operation
SET MARGIN MODE
n=0
E = 50s Pulse NO ++n = 25 YES NO VERIFY YES Last Addr NO ++ Addr
FAIL
YES RESET MARGIN MODE CHECK ALL WORDS 1st: VCC = 5V 2nd: VCC = 3V
AI03059B
2.7
Program Inhibit
Programming of multiple M27V322s in parallel with different data is also easily accomplished. Except for E, all like inputs including GVPP of the parallel M27V322 may be common. A TTL low level pulse applied to a M27V322's E input and VPP at 12V, will program that M27V322. A high level E input inhibits the other M27V322s from being programmed.
2.8
Program Verify
A verify (read) should be performed on the programmed bits to determine that they were correctly programmed. The verify is accomplished with GVPP at VIL. Data should be verified with tELQV after the falling edge of E.
2.9
On-Board programming
The M27V322 can be directly programmed in the application circuit. See the relevant Application Note AN620.
9/23
Device operation
M27V322
2.10
Electronic Signature
The Electronic Signature (ES) mode allows the reading out of a binary code from an EPROM that will identify its manufacturer and type. This mode is intended for use by programming equipment to automatically match the device to be programmed with its corresponding programming algorithm. The ES mode is functional in the 25C 5C ambient temperature range that is required when programming the M27V322. To activate the ES mode, the programming equipment must force 11.5V to 12.5V on address line A9 of the M27V322, with VPP = VCC = 5V. Two identifier bytes may then be sequenced from the device outputs by toggling address line A0 from VIL to VIH. All other address lines must be held at VIL during Electronic Signature mode. Byte 0 (A0 = VIL) represents the manufacturer code and byte 1 (A0 = VIH) the device identifier code. For the STMicroelectronics M27V322, these two identifier bytes are given in Table 3 and can be read-out on outputs Q0 to Q7.
2.11
Erasure operation (applies to UV EPROM)
The erasure characteristics of the M27V322 is such that erasure begins when the cells are exposed to light with wavelengths shorter than approximately 4000 A. It should be noted that sunlight and some type of fluorescent lamps have wavelengths in the 3000-4000 A range. Research shows that constant exposure to room level fluorescent lighting could erase a typical M27V322 in about 3 years, while it would take approximately 1 week to cause erasure when exposed to direct sunlight. If the M27V322 is to be exposed to these types of lighting conditions for extended periods of time, it is suggested that opaque labels be put over the M27V322 window to prevent unintentional erasure. The recommended erasure procedure for M27V322 is exposure to short wave ultraviolet light which has a wavelength of 2537 A. The integrated dose (i.e. UV intensity x exposure time) for erasure should be a minimum of 30 W-sec/cm2. The erasure time with this dosage is approximately 30 to 40 minutes using an ultraviolet lamp with 12000 W/cm2 power rating. The M27V322 should be placed within 2.5cm (1 inch) of the lamp tubes during the erasure. Some lamps have a filter on their tubes which should be removed before erasure. Table 2. Operating modes(1)
Mode Read Output Disable Program Program Inhibit Standby Electronic Signature
1. X = VIH or VIL, VID = 12V 0.5V.
E VIL VIL VIL Pulse VIH VIH VIL
GVPP VIL VIH VPP VPP X VIL
A9 X X X X X VID
Q15-Q0 Data Out Hi-Z Data In Hi-Z Hi-Z Codes
Table 3.
Electronic signature(1)
A0 VIL VIH Q7 0 0 Q6 0 0 Q5 1 1 Q4 0 1 Q3 0 0 Q2 0 1 Q1 0 0 Q0 0 0 Hex Data 20h 34h
Identifier Manufacturer's Code Device Code
1. Outputs Q15-Q8 are set to '0'.
10/23
M27V322
Maximum rating
3
Maximum rating
Stressing the device above the rating listed in the Absolute Maximum Ratings table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. Table 4.
Symbol TA TBIAS TSTG VIO
(2)
Absolute maximum ratings
Parameter Ambient Operating Temperature(1) Value -40 to 125 -50 to 125 -65 to 150 -2 to 7 -2 to 7 -2 to 13.5 -2 to 14 Unit C C C V V V V
Temperature Under Bias Storage Temperature Input or Output Voltage (except A9) Supply Voltage A9 Voltage Program Supply Voltage
VCC VA9(2) VPP
1. Depends on range. 2. Minimum DC voltage on Input or Output is -0.5V with possible undershoot to -2.0V for a period less than 20ns. Maximum DC voltage on Output is VCC +0.5V with possible overshoot to VCC +2V for a period less than 20ns.
11/23
DC and AC parameters
M27V322
4
DC and AC parameters
This section summarizes the operating and measurement conditions, and the DC and AC characteristics of the device. The parameters in the DC and AC Characteristic tables that follow are derived from tests performed under the Measurement Conditions summarized in the relevant tables. Designers should check that the operating conditions in their circuit match the measurement conditions when relying on the quoted parameters. Table 5. AC measurement conditions
High Speed Input Rise and Fall Times Input Pulse Voltages Input and Output Timing Ref. Voltages 10ns 0 to 3V 1.5V Standard 20ns 0.4V to 2.4V 0.8V and 2V
Figure 4.
AC testing input output waveform
High Speed 3V 1.5V 0V
Standard 2.4V 2.0V 0.8V
AI01822
0.4V
12/23
M27V322 Figure 5. AC testing load circuit
1.3V
DC and AC parameters
1N914
3.3k DEVICE UNDER TEST CL
OUT
CL = 30pF for High Speed CL = 100pF for Standard CL includes JIG capacitance
AI01823B
Table 6.
Symbol CIN COUT
Capacitance(1) (2)
Parameter Input Capacitance Output Capacitance Test Condition VIN = 0V VOUT = 0V Min Max 10 12 Unit pF pF
1. TA = 25 C, f = 1 MHz 2. Sampled only, not 100% tested.
13/23
DC and AC parameters Table 7.
Symbol ILI ILO ICC ICC1 ICC2 IPP VIL VIH(3) VOL VOH
M27V322 Read mode DC characteristics(1) (2)
Parameter Test Condition 0V VIN VCC 0V VOUT VCC E = VIL, GVPP = VIL, IOUT = 0mA, f = 5MHz E = VIH E > VCC - 0.2V VPP = VCC -0.6 0.7VCC IOL = 2.1mA IOH = -400A 2.4 Min Max 1 10 30 1 60 10 0.2VCC VCC + 0.5 0.4 Unit A A mA mA A A V V V V
Input Leakage Current Output Leakage Current Supply Current Supply Current (Standby) TTL Supply Current (Standby) CMOS Program Current Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage TTL
1. TA = -40 to 85 C or 0 to 70 C; VCC = 3.3V 10%; VPP = VCC 2. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP. 3. Maximum DC voltage on Output is VCC +0.5V.
Table 8.
Symbol ILI ICC IPP VIL VIH VOL VOH VID
Programming mode DC characteristics(1) (2)
Parameter Input Leakage Current Supply Current Program Current Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage TTL A9 Voltage IOL = 2.1mA IOH = -2.5mA 3.5 11.5 12.5 E = VIL -0.3 2.4 Test Condition VIL VIN VIH Min Max 10 50 50 0.8 VCC + 0.5 0.4 Unit A mA mA V V V V V
1. TA = 25 C; VCC = 6.25V 0.25V; VPP = 12V 0.25V 2. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP.
14/23
M27V322 Figure 6.
A0-A20
DC and AC parameters Read mode AC waveforms
VALID tAVQV E tGLQV GVPP tELQV Q0-Q15 tGHQZ Hi-Z tEHQZ tAXQX VALID
AI02207
Table 9.
Read mode AC characteristics(1) (2)
M27V322 Test Condition
Symbol
Alt
Parameter
-100(3)
-120
-150
Unit
Min Max Min Max Min Max tAVQV tELQV tGLQV tEHQZ(4) tGHQZ(4) tAXQX tACC tCE tOE tDF tDF tOH Address Valid to Output Valid Chip Enable Low to Output Valid Output Enable Low to Output Valid Chip Enable High to Output Hi-Z Output Enable High to Output Hi-Z Address Transition to Output Transition E = VIL, G = VIL G = VIL E = VIL G = VIL E = VIL E = VIL, G = VIL 0 0 5 100 100 50 45 45 0 0 5 120 120 60 50 50 0 0 5 150 150 60 50 50 ns ns ns ns ns ns
1. TA = -40 to 85 C or 0 to 70 C; VCC = 3.3V 10%; VPP = VCC 2. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP 3. Speed obtained with High Speed measurement conditions. 4. Sampled only, not 100% tested.
15/23
DC and AC parameters Figure 7. Margin mode AC waveforms
M27V322
VCC
A8
A9 tA9HVPH GVPP tVPHEL E tA10HEH A10 Set tEXA10X tEXVPX tVPXA9X
A10 Reset tA10LEH
AI00736B
1. A8 High level = 5V; A9 High level = 12V.
Table 10.
Symbol tA9HVPH tVPHEL tA10HEH tA10LEH tEXA10X tEXVPX tVPXA9X
Margin mode AC characteristics(1) (2)
Alt tAS9 tVPS Parameter VA9 High to VPP High VPP High to Chip Enable Low Test Condition Min 2 2 1 1 1 2 2 Max Unit s s s s s s s
tAS10 VA10 High to Chip Enable High (Set) tAS10 VA10 Low to Chip Enable High (Reset) tAH10 Chip Enable Transition to VA10 Transition tVPH tAH9 Chip Enable Transition to VPP Transition VPP Transition to VA9 Transition
1. TA = 25 C; VCC = 6.25V 0.25V; VPP = 12V 0.25V 2. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP.
16/23
M27V322 Figure 8.
A0-A20 tAVEL Q0-Q15 tQVEL VCC tVCHEL GVPP tVPHEL E tELEH tVPLEL tEHVPX DATA IN tEHQX
DC and AC parameters Programming and Verify modes AC waveforms
VALID tEHAX DATA OUT tEHQZ
tELQV
PROGRAM
VERIFY
AI02205
1. BYTE = VIH.
Table 11.
Symbol tAVEL tQVEL tVCHEL tVPHEL tVPLVPH tELEH tEHQX tEHVPX tVPLEL tELQV tEHQZ(3) tEHAX
Programming mode AC characteristics(1) (2)
Alt tAS tDS tVCS tOES tPRT tPW tDH tOEH tVR tDV tDFP tAH Parameter Address Valid to Chip Enable Low Input Valid to Chip Enable Low VCC High to Chip Enable Low VPP High to Chip Enable Low VPP Rise Time Chip Enable Program Pulse Width (Initial) Chip Enable High to Input Transition Chip Enable High to VPP Transition VPP Low to Chip Enable Low Chip Enable Low to Output Valid Chip Enable High to Output Hi-Z Chip Enable High to Address Transition 0 0 Test Condition Min 1 1 2 1 50 45 2 2 1 1 130 55 Max Unit s s s s ns s s s s s ns ns
1. TA = 25 C; VCC = 6.25V 0.25V; VPP = 12V 0.25V 2. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP. 3. Sampled only, not 100% tested.
17/23
Package mechanical
M27V322
5
Package mechanical
Figure 9. FDIP42W - 42 pin Ceramic Frit-seal DIP, with window (0.315" x 0.630"), package outline
A2 A3 A1 B1 B D2 D S
N
A L eA eB C
e1
K
1
E1
E
K1
FDIPW-b
1. Drawing is not to scale.
Table 12.
FDIP42W - 42 pin Ceramic Frit-seal DIP, with window (0.315" x 0.630"), mechanical data
millimeters inches Max 5.72 0.51 3.91 3.89 0.41 1.45 - 0.23 54.41 50.80 15.24 - - 14.50 2.54 14.99 - - 16.18 3.18 1.52 8.00 16.00 - - 4 42 1.40 4.57 4.50 0.56 - 0.30 54.86 - - 14.90 - - 18.03 4.10 2.49 - - 11 0.315 0.630 0.100 0.590 2.000 0.600 0.057 0.020 0.154 0.153 0.016 - 0.009 2.142 - - 0.571 - - 0.637 0.125 0.060 - - 4 42 Typ Min Max 0.225 0.055 0.180 0.177 0.022 - 0.012 2.160 - - 0.587 - - 0.710 0.161 0.098 - - 11
Symbol Typ A A1 A2 A3 B B1 C D D2 E E1 e eA eB L S K K1 N Min
18/23
M27V322
Package mechanical Figure 10. PDIP42 - 42 pin Plastic DIP, 600 mils width, package outline
A2 A1 B1 B D2 D S
N
A L eA eB C
e1
E1
1
E
PDIP
1. Drawing is not to scale.
Table 13.
Symbol
PDIP42 - 42 pin Plastic DIP, 600 mils width, package mechanical data
millimeters Typ Min - 0.25 3.56 0.38 1.27 0.20 52.20 50.80 15.24 - - 13.59 2.54 14.99 - - 15.24 3.18 0.86 0 42 Max 5.08 - 4.06 0.53 1.65 0.36 52.71 - - 13.84 - - 17.78 3.43 1.37 10 0.100 0.590 2.000 0.600 Typ inches Min - 0.010 0.140 0.015 0.050 0.008 2.055 - - 0.535 - - 0.600 0.125 0.034 0 42 Max 0.200 - 0.160 0.021 0.065 0.014 2.075 - - 0.545 - - 0.700 0.135 0.054 10
A A1 A2 B B1 C D D2 E E1 e1 eA eB L S N
19/23
Package mechanical
M27V322
Figure 11. SDIP42 - 42 pin Shrink Plastic DIP, 600 mils width, package outline
A2 A1 b2 b D2 D S
N
A L eA eB c
e
E1
1
E
SDIP
1. Drawing is not to scale.
Table 14.
SDIP42 - 42 lead Shrink Plastic DIP, 600 mils width, package mechanical data
millimeters inches Max 5.08 0.51 3.81 0.46 1.02 0.25 36.83 35.60 1.78 3.05 0.38 0.89 0.23 36.58 - - 15.24 13.72 15.24 18.54 3.30 0.64 42 2.54 3.56 0.130 0.025 42 0.100 12.70 4.57 0.56 1.14 0.38 37.08 - - 16.00 14.48 0.540 0.600 0.730 0.140 0.150 0.018 0.040 0.010 1.450 1.402 0.070 0.020 0.120 0.015 0.035 0.009 1.440 - - 0.600 0.500 0.180 0.022 0.045 0.015 1.460 - - 0.630 0.570 Typ Min Max 0.200
Symbol Typ A A1 A2 b b2 c D D2 e E E1 eA eB L S N Min
20/23
M27V322
Part numbering
6
Part numbering
Table 15.
Example:
Ordering information scheme
M27V322 -100 X F 1
Device Type M27
Supply Voltage V = 3.3V 10%
Device Function 322 = 32 Mbit (2Mb x16)
Speed -100 = 100 ns(1) -120 = 120 ns -150 = 150 ns
VCC Tolerance blank = 3.3V 10% X = 3.3V 5%
Package F = FDIP42W B = PDIP42 S = SDIP42
Temperature Range 1 = 0 to 70 C 6 = -40 to 85 C
1. High Speed, see AC Characteristics section for further information.
For a list of available options (Speed, Package, etc.) or for further information on any aspect of this device, please contact the STMicroelectronics Sales Office nearest to you.
21/23
Revision history
M27V322
7
Revision history
Table 16.
Date July 1999 02/09/00 03/01/01
Document revision history
Revision 0.1 1 2 First Issue Programming Flowchart changed (Figure 3) PRESTO III Programming Algorithm paragraph changed FDIP42W Package Dimension, L Max added (Table 12) SDIP42 Package added (Figure 11, Table 14) Document converted to new template (sections added, information moved). Packages are ECOPACK(R) compliant. SDIP42 package specifications updated (see Table 14 and Figure 11). Revision Details
22-May-2006
3
22/23
M27V322
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
(c) 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
23/23

▲Up To Search▲

Price & Availability of M27V322-100B1

	To Download M27V322-100B1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .